بمناسبة العام السابع هديتى للمنتدى كل شىء عن جهاز تارجت 901 العملاق Target-t901

[امام احمد]

اليوم هو لطريقه تحميل سوفتوير لجهاز التارجت العملاق
TARGET-T901

اغلق الرسيفر من الريموت وخليه في حالة stand by


افتح اللودر وهو يكون بهذا الشكل
ويمكنك تحميله من هنا
اللودر




سيظهر امامك اللودر الخاص بجهاز TARGRT
واتبع الصوره



بعد فتح اللودر اختر السوفتوير المناسب للجهاز
ويمكنك تحميل اخر سوفتوير من هنا


السوفت



سيتم اختبار السوفت كما فى الصور التاليه للتأكد من سلامته






بعد ذلك اختر الكوم المناسب لجهازك









اضغط على START لبدأ تحميل السوفت الى الرسيفر وانتظر قليلا




ستلاحظ تقدم عمليه التحميل كما فى الصوره



فى النهايه سيظهر على شاشه الرسيفر كلمه END
وهى دليل على اكتمال التحميل للرسيفر
افتح الرسيفر ويستحسن عمل ضبط مصنع


لعمل ضبط مصنع اتبع الاتى

اضغط menu من الريموت

وتابع الصور






ندخل الرقم السرى الماستر وهو
0901







وطبعا يمكنك تنزيل السوفت بالفلاشه بكل سهوله


اخوكم امام سليمان

[HTML]

======================
1.How to update s/w by PC?
======================
1) Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
2) Connect your PC and receiver with twisted RS-232C cable.
3) Turn on the receiver,
go to Main Menu-->STB Setting-->Output Setting
to switch Standby Mode to "PC Update"
and press "POWER" key to make it standby,
the LED dot will blink.
4) Run the update tool on your PC,Slect the <Download Main S/W>,
press <Open> and select the *** file,then click <Start>,upgrade will begin.
5) After finishing, the LED will display "-End"

======================
2.How to Enable Patch or Disable Patch?
======================
Press "F1" key, the LED will display 'H', then press '000'

======================
3.How to Edit Patch key?
======================
After Enable patch key,
Main Menu-->Installation-->Patch Menu

======================
4.How to update the Patch key?
======================
1) Download the softcam.key from the internet.
2) Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
2) Connect your PC and receiver with twisted RS-232C cable.
3) Turn on the receiver and press "POWER" key to make it standby, the LED dot will blink.
4) Run the update tool on your PC,Slect the <Download Key>,press <Open> and select
the softcam.key file,then click <Start>,upgrade will gin.
5) After finishing, the LED will display "-End"

======================
5.How to update STB-->STB
======================
a)Prepare a twisted RS232C cable(pin-2 to pin-3,pin-3 to pin-2,pin-5 to pin-5).
b)Connect the master receiver and the slave receiver with twisted RS-232C cable.
c)Turn on the master receiver and press "POWER" key to make it standby.
d)Turn on the slave receiver to begin update.
e)The LED of the master receiver will display "H" and blink it
f)Input the the password:
"111"(S/W).
"222"(Data**** Channel List).
"333"(S/W)+Data****).

g)During the updating,the LED of the slave receiver will display "Rxxx"(Receive the data to the SDRAM),"-ES-"(Erase the flash),then "Pxxx"(Put the date to the flash),at last it will display "-End"
h)Tune off the slave receiver,disconnect RS-232C cable and restart it
i)If you want to update another receiver,replace it with another receiver and turn on the receiver,it will start without inputting password.

=============================
6.Download Start-up/Radio Log
=============================
Support Picture Format: JPG, BMP

================================
7.Hot Keys
================================
a) F1 + 000: Patch Enable/Disable
b) F1 + 111: Rs232 Mode list
c) F1 + 555: Ethernet IP Setting (Only when Ethernet CSC selected)
d) F1 + 666: Ethernet Server Setting (Only when Ethernet CSC selected)
e) F1 + 777: Reboot Receive
[/HTML]